Skip to main content
Skip to main content

🪵 Flooring Safety

Topic: Chemical exposure, knee protection, respiratory hazards, slip prevention, power tools, ergonomics, and silica Duration: 7–10 minutes Required: OSHA 29 CFR 1926.1153 (Silica), 1910.1200 (Hazard Communication), 1926 Subpart I (PPE)

The Stats​

  • Knee injuries from prolonged kneeling — flooring installers have among the highest rates of knee disorders; many require surgery or early retirement
  • Silica exposure from concrete grinding/prep — respirable silica causes silicosis; OSHA estimates 2.3 million workers exposed
  • Chemical exposure — Adhesives and sealers contain VOCs and solvents; skin and respiratory irritation, dizziness, and long-term effects
  • Slip/fall incidents — Wet adhesives, fresh sealers, and uneven substrates cause sprains, fractures, and head injuries
  • Power tool injuries — Saws, grinders, and nailers cause lacerations, amputations, and eye injuries when used improperly

OSHA requires: Silica exposure control when grinding concrete; SDS for adhesives/sealers; PPE as specified by hazard assessment; eye and hearing protection for power tools.

Chemical Exposure (Adhesives, Sealers, Coatings)​

Before Use​

  • Read the SDS — Know hazards, PPE, and first aid
  • Ventilation — Open doors, windows; use fans; avoid confined spaces
  • Skin protection — Chemical-resistant gloves; long sleeves if needed
  • Eye protection — Safety glasses or goggles when splashing is possible

During Use​

  • Minimize skin contact — Wash immediately if contact occurs
  • No eating/drinking — In application area
  • Curing time — Allow adequate cure before heavy traffic or next trade

Storage & Disposal​

  • Sealed containers — Keep lids on when not in use
  • Proper disposal — Per SDS and local regulations

Knee Injuries (Prolonged Kneeling)​

DoDon't
Use knee pads or kneeling matsKneel directly on hard surfaces
Take breaks every 20–30 minutesKneel for hours without rest
Alternate tasks (standing, kneeling)Ignore knee pain or swelling
Use ergonomic tools (long-handled rollers)Strain in awkward positions

Knee pads — Choose padded or gel inserts; ensure proper fit and comfort.

Respiratory Hazards (Dust from Grinding & Sanding)​

Silica from Concrete Prep​

  • Wet methods — Use water to suppress dust when grinding
  • Vacuum — HEPA vacuum on grinders when possible
  • Respirator — N95 minimum for dust; half-face or full-face if exposure exceeds limits
  • Avoid breathing dust — Stay upwind; limit exposure time

General Dust​

  • Sanding — Use dust collection; respirator for fine dust
  • Sweeping — Wet sweep or vacuum; avoid dry sweeping

Slip Hazards During Installation​

HazardPrevention
Wet adhesiveBarricade area; post "Wet Floor" signs; allow cure time
Fresh sealerKeep foot traffic off until dry
Uneven substrateFill holes; level before install
Cords and hosesRoute out of walkways; use cord covers
SpillsClean immediately; absorbent for adhesives

Tool Safety (Power Saws, Grinders, Nailers)​

Power Saws (Tiles, Hardwood)​

  • Guards — Keep blade guards in place and functional
  • Blade — Correct blade for material; sharp and undamaged
  • Hearing protection — Required when noise exceeds 85 dB
  • Eye protection — Safety glasses or face shield
  • Cords — Inspect for damage; use GFCI

Grinders​

  • Guard — Wheel guard in place
  • Wheel — Correct type; not cracked or worn
  • PPE — Face shield, hearing protection, respirator for dust
  • Two-hand grip — Maintain control

Nailers / Staplers​

  • Safety trigger — Never bypass
  • Direction — Never point at anyone
  • Disconnect — Depressurize when not in use
  • Jams — Disconnect before clearing

Ergonomic Injuries​

  • Lift correctly — Bend knees, keep load close; team lift heavy boxes
  • Work height — Work at waist height when possible
  • Stretch — Warm up; stretch neck, back, wrists, knees
  • Vary tasks — Rotate between cutting, fitting, and installing

Discussion Questions​

  1. What adhesives or sealers are we using today? Have we read the SDS?
  2. What knee protection are we using? Who has knee pads or kneeling mats?
  3. Are we grinding or sanding concrete? What's our silica control (wet, vacuum, respirator)?
  4. What power tools are we using? Are guards and PPE in place?

Today's Commitment​

"I will use knee protection, read SDSs for chemicals, wear a respirator when creating dust, and keep guards on all power tools."

Sign-In​

NameSignatureCompany

Presenter: _________________ Date: _________